With this new Autopilot Concept Change I decided to move on from Shields build my own Barebone arduino. A bold move but necessary for the future of this project. The major problems with is their size. Now it you don't have a problem with size and weight and Shields is for you. But the most annoying thing about them is the fact that honing on your electronic and soldering skills is no longer expected which I feel is the biggest short change any inventor can do. Hence came the Atmel328 microprocessor. That's right! Every Arduino Uno processing is done by one. So you might just as well get to know it. There's plenty of others but the simple interface of the Arduino IDE, makes this a breeze to program. I need to upload the bootloader (quite easy). A quick trick to change programmer to "Arduino as ISP" and change the board type. It's a no brainer: one Arduino Uno costs R300. Total cost of putting a working Barebone is less than

After a bad case of stomach bug, I stayed at home today and got working on he UAV both hardware and software. The goal was simple yet daunting: Transfer 3 shields worth of hardware to one protoshield. Due to the high turnaround of making a custom-made PCB (which I have a fair experience on). I decided to go the perfboard route and make the conceptual design straight on the board. It became quite obvious that a few things could be done to reduce the size of the hardware: Instead of having the 5V regulator (although it will be added as a bakcup option) power supply could be taken straight from the ESC. I measured a voltage of 5.05V The need of transistors on each servo channel can be replaced with the switching done in the controller. This can be managed more efficiently. The sensors are attached on the board using right-angled header pins allowing the sensor boards to stacked upright leaving space for more sensors such as a barometer, and the prize sensor: the GPS. Having mad...

So I managed to wire the OpenLog sensor and ran some few read/write code to make sure the wiring works as expected. And it works!!! This device will enable me to log any data that will be used for the flight controller design. This is prior to mounting a GPS sensor for waypoint tracking. The SoftwareSerial library has been used instead of the serial pins 0 and 1 so that only selective streams will be logged while leaving the option for bebug logging. On the custom board, I'll have to accommodate for quick removal of the OpenLog board in the event Logging us required somewhere else.

My new logger sensor finally arrived!!! Since my MicroSD shield died on me, I realised that I needed to serial logger to be able to collect data for flight controller design. I also realised that getting the OpenLog board will expand the capability of the autopilot. The best thing about this board is its size. Being only a few grams and just over 1cm across each side one thing left to do: wire it up! I'm in the process to finishing the 'LOGGING_MODE' of the 'autopilot'. This should be able to still maintain control of the glider and capture of the necessary inputs to begin flight controller design. I'll keep you posted!

So After making my hot wire cutter , I realised that I still needed a portable devices to make grooves, channels and enclosures in the fuselage body. So came a brilliant idea. Replace the tip of a soldering iron with a solid 2mm diameter copper wire. The wire is ductile so it can be shaped in any form desired. I found out though that the length of wire is important as that determines cutting temperature. Too long and the wire is too cold to melt foam. Too short and the wire "over-melt" the foam instead. With this device, foam has become the next best thing when it comes to airplane design and build. The complexity of the design is only left up to the imagination of the designer! Below are some examples of what this awesome tool can do.

So I've finally arrived at a time all aircraft engineers hope to get... Maiden flight. But I've had too many experiences where the maiden flight is all but over in a matter of seconds becauseI was too eager to "free the bird". The end result... A disgruntled soul wishing it had been more patient. I've learnt my lesson (with my wife's mentoring) to be more methodical and pragmatic about my approach to the maiden flight. Since I don't have the luxury of wind tunnel testing of the wing and the airframe, the only reliable weapon in my arsenal was... Calculations. To be more specific, weight and balance calculations and measurements. After using AutoCAD, a weight balance spreadsheet to calculate the estimated (emphasis on "estimated") center of gravity in relation to the wing mac (mean aerodynamic chord), measuring the actual cg will all electronics included was the next (and hopefully) final step. It must be said that prior to this step I reali...

It's really frustrating when you buy a piece of hardware without thoroughly reading the feedback comments from different users. Well this was the case when I got myself a MicroSD shield from SparkFun . At first it worked very nice with the different libraries giving you quite an array of choices in terms of what you can do with the field. But the major drawback was that it took FIVE digital pins out the the Arduino to work namely: MOSI - pin 11 MISO - pin 12 CLK - pin 13 CS - pin 4 ChipSelect - pin 8 - Pin 10 also needed to remain as an OUTPUT for the shield to remain operational. This was in direct conflict with servo controller board. So it was quite clear that given the number of inputs (i.e servos, sensors etc...), this was going to cripple the development of the flight controller and perhaps prevent the continuation of this project. So a broken MicroSD shield forced me to look at alternative for a data logger and there came the OpenLog device , with simply connects t...

Like most engineering processes, the ability to perform concurrent processes always lead to a more efficient and flexible product. Having said that, It is often prudent to not "eat more than you can chew" referring to developing electronics and an UAV airframe concurrently. Throwing caution out the wind and the fact that building 'foamies' is one of the easiest and quickest way to get an airplane concept in the air, the objective was clear... Build my own hot wire cutter. This little piece of magic hardware, will save you hours of foam sanding and cutting ( Or countless hours of balsa cutting and gluing). So after some research (quite a bit actually) a came across this piece of document that helped spec my power supply, and wire. I added a motor speed controller (which I had to assemble/solder myself - nerve-wrecking!) to easily regulate the temperature of the hot wire in between cuts. I know it's popular to use light dimmers but the motor controller seemed...

Like all electronics projects, the skill of "PCB making" is of paramount consequence. After doing my research, I finally assembled the ingredients to develop a servo control PCB. The Goal: I wanted the UAV to have be capability of Manual or Autopilot Mode while in flight as a safety option. This was to be controlled by the Control Station (RC transmitter for now) using a switch. The Parts: Single sided PCB board PCB toner transfer paper (I tried using HP Photosmart paper - DIDN'T WORK) Clothing Iron - Temperature set on "Medium" Wooden cutting board (Just beg the wife!) Ferric Chloride Solution (Here in SA try Mantech or RS Online Drill Machine Drill bits (0.6mm or 0.8mm). I used 0.8mm.  Plastic gloves (Please wife!) Plastic Container (Any container will do as long as it's plastic). So as the point 2 say, I tried using HP Photosmart paper  but it failed dismally. The glossy side of the paper melted and got stuck to the copper clad and it ...

It took me a while to figure out how transistors  work. Although the theory is quite simple, the application was  something else. The goal was simple: To use the RC transmitter Channel 5 switch to "switch" ON or OFF "Manual Mode" in the micro-controller. This will enable the ground station to override control of the UAV in any time of the mission flight. Again goal simple enough. The application in many respect was simple enough. what was needed was to understand the signal range of the the transmitter switch in order to raise or lower the base current of the transistor for signal input. The objective is to be able to switch between AutoPilot and Manual mode using a switch on the RC transmitter. Hope I get there!